ACT20P-BRIDGE-P
Product image
ACT20P-BRIDGE-P
Electric symbol
ACT20P-BRIDGE-P
ACT20P-BRIDGE-P
Dimensioned drawing
ACT20P-BRIDGE-P
Example of use
ACT20P-BRIDGE-P

ACT20P-BRIDGE-P

Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V

Ürün No. 2456820000
Veri sayfasını indir Engineering Support Software Support Product Downloads
Aksesuarlar 2 Münferit parçalar 1 İlgili ürünler 2
Approvals General ordering data Dimensions and weights Temperatures Probability of failure Environmental Product Compliance Input Output Output (digital) General data Insulation coordination Connection data Important note Classifications

Approvals

Approvals
![](https://mdcop.weidmueller.com.cn/mediadelivery/rendition/900_319222/-S800/-T1z1mm-S80)  
Approvals
CULUS;  
ROHS
Conform  

General ordering data

Version
Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V  
Order No.
2456820000  
Type
ACT20P-BRIDGE-P  
GTIN (EAN)
4050118471762  
Qty.
1  adet

Dimensions and weights

Depth
113,6  mm
Depth (inches)
4,472  inch
Height
127,1  mm
Height (inches)
5,004  inch
Width
22,5  mm
Width (inches)
0,886  inch
Net weight
205  g

Temperatures

Storage temperature
-40 °C...85 °C  
Operating temperature
-20 °C...60 °C  
Humidity at operating temperature
0...95 % (no condensation)  
Humidity
10…90 %, no condensation  

Probability of failure

SIL in compliance with IEC 61508
None  

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption  
RoHS Exemption (if applicable/known)
7a, 7cI  
REACH SVHC
Lead 7439-92-1  
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924  

Input

Bridge sensitivity
1.0 mV / V to 5.0 mV / V  
Bridge supply voltage
5 V or 10 V  
Input signal
±10 mV / ±20 mV / ±30 mV / ±50 mV  
Number of inputs
1  
Sensor
Strain gauge resistance  
Resistance measurement  
Total resistance of all parallel resistance measuring bridges: min. 87 Ω  
Sensor supply
120 mA @ 10 V (= 4 x 350 Ω bridge resistors)  

Output

Load impedance current
≤ 600 Ω  
load impedance voltage
600 Ω  
Output current
0…22 mA (adjustable)  
Output voltage, note
0…11 V (adjustable)  
Type
active  
connected control must be passive  

Output (digital)

Max. switching voltage, AC
0  V
Rated switching current
0.1 A  

General data

Accuracy
<0.05 % of measuring range  
Configuration
DIP switch and button  
Linearity
Typically ± 0.05 % of signal range  
Long-term drift
0.1 % / 10.000 h  
Nominal power consumption
2  VA
Operating altitude
≤ 2000 m  
Power consumption
3 W @ 24 V DC  
Protection degree
IP20  
Rail
TS 35  
Step response time
<400 ms (10…90 %)  
Temperature coefficient
typ. 0.005 % / °C  
Voltage supply
10…60 V DC  

Insulation coordination

EMC standards
EN 61326  
Insulation voltage
5.7 kV (input / output, input / supply)  
Pollution severity
2  
Rated voltage
300 V  
Surge voltage category
III  

Connection data

Type of connection
PUSH IN  
Tightening torque, min.
0,4  Nm
Tightening torque, max.
0,6  Nm
Clamping range, rated connection
2,5  mm²
Clamping range, min.
0,5  mm²
Clamping range, max.
2,5  mm²
Wire connection cross section AWG, min.
AWG 26  
Wire connection cross section AWG, max.
AWG 14  
Wire cross-section, solid, min.
0,2  mm²
Wire cross-section, solid, max.
2,5  mm²
Wire connection cross section, finely stranded, min.
0,2  mm²
Wire connection cross section, finely stranded, max.
2,5  mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min.
0,2  mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max.
2,5  mm²

Important note

Product information
The ACT20P-BRIDGE-P bridge measuring transducer converts measuring bridge voltages into standard signals. Buttons are used for adjustment to the measuring bridge connected. The bridge measuring transducer can supply up to 4 parallel-connected measuring bridges each with 350 Ω. The device supports simple compensation of the tare weight with a separate input for an external button or an external PLC signal. The power supply is galvanically isolated from input and output (3-way isolation).T

Features
  • 4-wire and 6-wire measurement
  • Supply of up to 4 parallel-connected measuring bridges each with 350 Ω
  • Input and output ranges can be adjusted via DIP switches
  • Tare compensation via external button or PLC signal
  • Front LED indicates operation status
  • 3-way galvanic isolation between input, output and power supply
 

Classifications

ETIM 6.0
EC002653  
ETIM 7.0
EC002653  
ETIM 8.0
EC002653  
ETIM 9.0
EC002653  
ETIM 10.0
EC002653  
ECLASS 9.0
27-21-01-20  
ECLASS 9.1
27-21-01-20  
ECLASS 10.0
27-21-01-20  
ECLASS 11.0
27-21-01-20  
ECLASS 12.0
27-21-01-20  
ECLASS 13.0
27-21-01-20  
ECLASS 14.0
27-21-01-20  
ECLASS 15.0
27-21-01-20