ACT20P-BRIDGE-P
Product image
ACT20P-BRIDGE-P
Electric symbol
ACT20P-BRIDGE-P
ACT20P-BRIDGE-P
Dimensioned drawing
ACT20P-BRIDGE-P
Example of use
ACT20P-BRIDGE-P

ACT20P-BRIDGE-P

Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V

Ürün No. 2456820000
Veri sayfasını indir Engineering Support Software Support Product Downloads
Aksesuarlar 2 Münferit parçalar 1 İlgili ürünler 2
General ordering data Dimensions and weights Temperatures Probability of failure Environmental Product Compliance Input Output Output (digital) General data Insulation coordination Connection data Important note Classifications Approvals

General ordering data

Version
Measuring bridge converter, Input : Resistance measuring bridge, Output : 0(4)-20 mA, 0-10 V  
Order No.
2456820000  
Type
ACT20P-BRIDGE-P  
GTIN (EAN)
4050118471762  
Qty.
1  adet

Dimensions and weights

Depth
113,6  mm
Depth (inches)
4,472  inch
Height
127,1  mm
Height (inches)
5,004  inch
Width
22,5  mm
Width (inches)
0,886  inch
Net weight
205  g

Temperatures

Storage temperature
-40 °C...85 °C  
Operating temperature
-20 °C...60 °C  
Humidity at operating temperature
0...95 % (no condensation)  
Humidity
10…90 %, no condensation  

Probability of failure

SIL in compliance with IEC 61508
None  

Environmental Product Compliance

RoHS Compliance Status
Compliant with exemption  
RoHS Exemption (if applicable/known)
7a, 7cI  
REACH SVHC
Lead 7439-92-1  
SCIP
2f6dd957-421a-46db-a0c2-cf1609156924  

Input

Bridge sensitivity
1.0 mV / V to 5.0 mV / V  
Bridge supply voltage
5 V or 10 V  
Input signal
±10 mV / ±20 mV / ±30 mV / ±50 mV  
Number of inputs
1  
Sensor
Strain gauge resistance  
Resistance measurement  
Total resistance of all parallel resistance measuring bridges: min. 87 Ω  
Sensor supply
120 mA @ 10 V (= 4 x 350 Ω bridge resistors)  

Output

Load impedance current
≤ 600 Ω  
load impedance voltage
600 Ω  
Output current
0…22 mA (adjustable)  
Output voltage, note
0…11 V (adjustable)  
Type
active  
connected control must be passive  

Output (digital)

Max. switching voltage, AC
0  V
Rated switching current
0.1 A  

General data

Accuracy
<0.05 % of measuring range  
Configuration
DIP switch and button  
Linearity
Typically ± 0.05 % of signal range  
Long-term drift
0.1 % / 10.000 h  
Nominal power consumption
2  VA
Operating altitude
≤ 2000 m  
Power consumption
3 W @ 24 V DC  
Protection degree
IP20  
Rail
TS 35  
Step response time
<400 ms (10…90 %)  
Temperature coefficient
typ. 0.005 % / °C  
Voltage supply
10…60 V DC  

Insulation coordination

EMC standards
EN 61326  
Insulation voltage
5.7 kV (input / output, input / supply)  
Pollution severity
2  
Rated voltage
300 V  
Surge voltage category
III  

Connection data

Type of connection
PUSH IN  
Tightening torque, min.
0,4  Nm
Tightening torque, max.
0,6  Nm
Clamping range, rated connection
2,5  mm²
Clamping range, min.
0,5  mm²
Clamping range, max.
2,5  mm²
Wire connection cross section AWG, min.
AWG 26  
Wire connection cross section AWG, max.
AWG 14  
Wire cross-section, solid, min.
0,2  mm²
Wire cross-section, solid, max.
2,5  mm²
Wire connection cross section, finely stranded, min.
0,2  mm²
Wire connection cross section, finely stranded, max.
2,5  mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, min.
0,2  mm²
Wire connection cross-section, finely stranded with wire-end ferrules DIN 46228/4, max.
2,5  mm²

Important note

Product information
The ACT20P-BRIDGE-P bridge measuring transducer converts measuring bridge voltages into standard signals. Buttons are used for adjustment to the measuring bridge connected. The bridge measuring transducer can supply up to 4 parallel-connected measuring bridges each with 350 Ω. The device supports simple compensation of the tare weight with a separate input for an external button or an external PLC signal. The power supply is galvanically isolated from input and output (3-way isolation).T

Features
  • 4-wire and 6-wire measurement
  • Supply of up to 4 parallel-connected measuring bridges each with 350 Ω
  • Input and output ranges can be adjusted via DIP switches
  • Tare compensation via external button or PLC signal
  • Front LED indicates operation status
  • 3-way galvanic isolation between input, output and power supply
 

Classifications

ETIM 6.0
EC002653  
ETIM 7.0
EC002653  
ETIM 8.0
EC002653  
ETIM 9.0
EC002653  
ETIM 10.0
EC002653  
ECLASS 9.0
27-21-01-20  
ECLASS 9.1
27-21-01-20  
ECLASS 10.0
27-21-01-20  
ECLASS 11.0
27-21-01-20  
ECLASS 12.0
27-21-01-20  
ECLASS 13.0
27-21-01-20  
ECLASS 14.0
27-21-01-20  
ECLASS 15.0
27-21-01-20  

Approvals

Approvals
![](https://mdcop.weidmueller.com.cn/mediadelivery/rendition/900_319222/-S800/-T1z1mm-S80)  
Approvals
CULUS;  
ROHS
Conform