Skip to content Skip to navigation menu

Download data sheet Related products

ACT20X-HTI-SAO-S

EX signal isolating converter, Ex-input: I,ϑ, Safe-output: 4-20mA, 2-channel, Input : Temperature, 0-20 mA, Output : 0(4)-20 mA

Item No. 8965470000

Properties

General ordering data

Version	EX signal isolating converter, Ex-input: I,ϑ, Safe-output: 4-20mA, 2-channel, Input : Temperature, 0-20 mA, Output : 0(4)-20 mA
Order No.	8965470000
Type	ACT20X-HTI-SAO-S
GTIN (EAN)	4032248785087
Qty.	1 items

Dimensions and weights

Depth	113.6 mm
Depth (inches)	4.472 inch
Height	119.2 mm
Height (inches)	4.693 inch
Width	22.5 mm
Width (inches)	0.886 inch
Net weight	178 g

Temperatures

Storage temperature	-20 °C...85 °C
Operating temperature	-20 °C...60 °C
Humidity	0...95 % (no condensation)

Probability of failure

SIL PAPER	SIL certificate
SIL in compliance with IEC 61508	2
MTBF	111 a

Environmental Product Compliance

RoHS Compliance Status	Compliant with exemption
RoHS Exemption (if applicable/known)	7a, 7cI
REACH SVHC	Lead 7439-92-1
SCIP	2f6dd957-421a-46db-a0c2-cf1609156924

Assembling

Mounting position	horizontal or vertical
Rail	TS 35
Type of mounting	DIN rail Snap mounting support rail

Input EX

Input current	0...20 mA 4…20mA
Input resistance, current	20 Ω + PTC 50 Ω
Line resistance in measuring circuit	≤ 50 Ω
Sensor	2-/3-/4-wire RTD: PT10, PT20, PT50, PT100, PT250, PT300, PT400, PT500, PT1000, Ni50, Ni100, Ni120, Ni1000 Thermocouples: B, E, J, K, N, R, S, T ; in compliance with IEC 60584-1 and L, U in compliance with DIN43710
Temperature input range	Configurable PT100: -200…+850 °C K: (-180…+1372 °C) L: (-200…+900 °C) N: (-180…+1300 °C) R: (-50…+1760 °C) S: (-50…+1760 °C) T: (-200…+400 °C) U: (-200…+600 °C) W3: (0…+2300 °C) W5: (0…+2300 °C) LR: (-200…+800 °C) PT200: -200…+850 °C PT1000: -200…+850 °C NI100: -60°C…+250 °C Ni120: -80 °C…+320 °C NI1000: -60°C…+250 °C B: +100…+1820 °C E: (-100…+1000 °C) J: (-100…+1200 °C)
Type	intrinsically safe circuit RTD, TC, DC (mA)

Output

Influence of load resistance	≤ 0.01% of span / 100 Ω
Load impedance current	≤ 600 Ω
Output current	0…23 mA, configurable: 0…20 / 4…20 / 20…0 / 20…4 mA configurable downscale (3.5 mA) ⁄ upscale (23 mA) @ error
Output signal limit	3.8…20.5 mA / 0…20.5 mA (dependent on range)
Type	active (as current source) or passive (as current sink)

Alarm output

Alarm function	Line interruption at the input Short circuit at input No supply voltage Device error
Continuous current	≤ 0.5 A AC / 0.3 A DC (safe zone) ≤ 0,5 A AC / 1 A DC (zone 2)
Nominal switching voltage	≤ 125 V AC / 110 V DC (safe area) ≤ 32 V AC / 32 V DC (zone 2)
Power rating	≤ 62.5 VA / 32 W (safe area) ≤ 16 VA / 32 W (Zone 2)
Type	Status relay 1 NC (voltage-free)

General specifications

Configuration	With FDT/DTM software Requires configuration adapter 8978580000 CBX200 USB
Humidity	0...95 % (no condensation)
Operating altitude	≤ 2000 m
Power consumption	≤ 0.8 W
Protection degree	IP20
Step response time	≤ 400 ms (with current) ≤ 1 s (with temperature)
Type of connection	Screw connection
Voltage supply	19.2…31.2 V DC

Insulation coordination

EMC standards	EN 61326-1
Insulation voltage	2.6 kV (input / output)
Rated voltage	300 V
Standards	EN 61010-1

Data for Ex applications (ATEX)

Current I₀	18.4 mA
Installation location	Device installed in safe area, zone 2
Marking	II (1) G [Ex ia Ga] IIC/IIB/IIA II (1) D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Power P₀	40 mW
Voltage U₀	8.7 V DC

Safety-related basic specifications

Description of the "safe state"	analogue Output ≤ 3.6 mA or output ≥ 21 mA
Device type	B
Diagnostic test interval	30 s
T_proof	3 a
Total failure rate for safe detected failures (λ_SD)	0 FIT
Hardware fault tolerance (HFT)	0
Safety category	SIL 2
Safe Failure Fraction (SFF)	90 %
Mean Time To Repair (MTTR)	24 h
Total failure rate for safe undetected failures (λ_SU)	234 FIT
Total failure rate for dangerous detected failures (λ_DD)	367 FIT
Total failure rate for dangerous undetected failures (λ_DU)	61 FIT
Probability of outage PFH	6.1 x 10^-8 h^-1
Demand mode	High
Demand rate	3,000 s
Demand response time	Signal input: <0.5 s (opto output) Temperature input: <1.1 s (opto output)

Average Probability of Failure on Demand (PFD_avg)

3.96 x 10^-4 (T_proof = 1 year)
6.5 x 10^-4 (T_proof = 2 years)
1.41 x 10^-4 (T_proof = 5 years)

Connection data

Type of connection	Screw connection
Tightening torque, min.	0.4 Nm
Tightening torque, max.	0.6 Nm
Clamping range, rated connection	2.5 mm²
Clamping range, min.	0.25 mm²
Clamping range, max.	2.5 mm²
Wire connection cross section AWG, min.	AWG 26
Wire connection cross section AWG, max.	AWG 12

Guarantee

Time interval

3 years

Downloads

Approval/Certificate/Document of Conformity	Certification SIL Certification DNV GL Certification ATEX Certification IECEx Certification UL UL certification for canada Declaration of Conformity
Engineering Data	CAD data -- STEP
Eplan Data Portal	Eplan data
CADENAS eCATALOG	CAX data
Software	WI-Manager, DTM-Library for online installation Release notes for Weidmueller FDT-DTM Software version
User Documentation	Instruction sheet Safety Manual for SIL application Handbuch ACT20X- Serie, deutsch Manual ACT20X- series, english 20210120 Security Advisory - WI-Manager affected by MundM Software fdtCONTAINER vulnerability Measuring range table
Catalogues	Catalogues in PDF-format

Classifications

ETIM 6.0	EC002919
ETIM 7.0	EC002919
ETIM 8.0	EC002919
ETIM 9.0	EC002919
ETIM 10.0	EC002919
ECLASS 9.0	27-21-01-29
ECLASS 9.1	27-21-01-29
ECLASS 10.0	27-21-01-29
ECLASS 11.0	27-21-01-29
ECLASS 12.0	27-21-01-29
ECLASS 13.0	27-21-01-29
ECLASS 14.0	27-21-01-29
ECLASS 15.0	27-21-01-29

Tender specification sheets

Long specification

Short specification

Ex- temperature transducer for RTD-/ TC temperature signals and DC current signals
1-channel temperature transducer in 22.5 mm width with external power supply,
for capturing and isolating RTD- / TC- sensor and DC current signals (0(4)...20 mA) from
Ex zones 0,1,2. The output can be operated in the safe zone either as an active signal (0(4)...20 mA) or
as a passive 4...20 mA current loop.
Status and error messages are available via a relay contact (NO).
The component can be configured using standard FDT/DTM software.

Approvals